providing a window into the process. Rev: n/a. P/N: n/a. ECO: n/a. Dynisco 1/8 DIN Indicator. Concise Product Manual Cleaning Tool Kit, Machining Tool Kit, Indicator , Process. Readout UPR , Process Controller ATC For additional options please contact the factory. For additional options please consult factory. Accessories. Indicator , Process Readout UPR, Process Controller ATC,. Cleaning Tool Kit, Machining.

Author: Shaktigal Vudozahn
Country: Solomon Islands
Language: English (Spanish)
Genre: Music
Published (Last): 22 August 2017
Pages: 66
PDF File Size: 5.7 Mb
ePub File Size: 16.17 Mb
ISBN: 352-2-53507-400-7
Downloads: 10923
Price: Free* [*Free Regsitration Required]
Uploader: Nikokazahn

C6 – Retransmission current output minimum value – adjust to Alarm 0 means that the device has no status alarm variation to send.

PCD 03 Instruction Man Slide the panel fynisco from the rear over the instrument case so that the snap-in elements of the mounting frame engage in the recesses on the sides. Roulette Set 3D model. A digital input that can be configured for either resetting the alrams or triggering hold on value.

This value MUST be set equal to the sensor full range, e. Attribute Description Every variable has one or more of the following attributes: Use the up and down arrow keys to set the appropriate alarm set-point.

The communication speed is selectable among, and baud. The content of this manual must be read, understood 13990 followed in its entirety. Related 3d models searches:.

Digital pressure indicator / for melt / process – PTE, PTE – Dynisco

Please call for a return authorization number RA before returning any product. On Press the FUNC button to perform the full scale calibration The indicator automatically dynico to operating mode after 6 seconds if no changes are made.


Decimal Digits The decimal point that may be present in the value is ignored. Decimal figure assigned to: The new values will be enabled but they will be lost when the instrument is powered down.

▷ dynisco 3d models・grabcad

RTU is a binary method with byte format composed as follows: Automatic detection of maximum and minimum measured value. Hold-On Value Hol The external contact can be used to freeze input signal sampling, holding the last measured value for use on the display, alarms, retransmission etc.

Use the and keys to modify this parameter.

Each slave has a unique address ranging from 1 to See note 6 at page The display only shows the number of counts for the digital to analog converter. Press the FUNC key to initialize zero calibration.

The indicator automatically returns to the normal operating mode after 6 seconds if no changes are made. This error message disappears automatically after 3 seconds.

Slide mounting clips fully forward with the y side toward the front until base is secure in panel. Address Space The whole variables are addressable as word as well as bit; the user may choose the better way according to the condition. Using the Up arrow key, advance the legend to LO. Resolution and decimal point position are as selected for the readout value. Resolution and decimal position are as selected for the readout value. CE-Declaration of Conformity 38 Created with VRay, and need this renderer to work correctly.


The alarm must have been programmed as a low alarm. If the error persists, return the instrument to your supplier. After reading, the word is set to 0 if the value read is 3 or 4. Only the numerical value will be shown during modification. OFF for no filter on alarm threshold, or xxx for filter with the time constant chosen in step C above.

The instrument automatically returns to operating mode after 6 seconds if no changes are made. If a fault condition is detected, 1309 display will show the message Er followed by an error code.

OFF for no filter on retransmitted value, or xxx for filter having the time constant chosen in step C.

Default values are shown on 13990 Loc or UnLoc UnLoc.

Dynisco 1390 Indicator Series

The analog retransmission and alarm go low scale or high scale as a failsafe configuration. CL if function selected above is performed with contact closed, or OP if function selected above is performed with contact open. Er Error during internal autozero measurement for temperature drift compensation.

Next post: