Standards. DIN Manufacturing processes joining – Part 5: Joining by forming processes; Classification, subdivision, terms and definitions. Title ( German). DIN references following documents: DIN , , Manufacturing processes joining – Part 5: Joining by forming processes; Classification. Find the most up-to-date version of DIN at Engineering
|Genre:||Health and Food|
|Published (Last):||8 September 2007|
|PDF File Size:||3.3 Mb|
|ePub File Size:||5.73 Mb|
|Price:||Free* [*Free Regsitration Required]|
Air and Exhaust manage From all sheets and rivet specimens arrangements the highest load capacity of the joint was obtained for cin DC01 sheet material joints, and the lowest load capacity of the joint was obtained for the EN AW sheet material joints.
Joining by Upset Bulging
Their properties must match to the cases to be tested. Clinching allows for joining of both similar and different materials. The English translation is believed to be accurate. EN,Eurocode 3, Design of steel structures, Part The overall thickness of the joining partners must not exceed 5 mm. Living reference work entry First Online: For the four joining systems the lap joint specimens were made and tested in the shearing test.
It is the joining of at least two overlapping sheet metal, tube or profile parts achieved by means of cold deformation with punch and die. J Clean Prod 19 6—7: There are no generally applicable values for the base thickness tb. The joints were prepared for the three combinations of the DC01 steel and EN AW- aluminium alloy sheets with the thickness of 2mm.
Especially for round joints, care must be taken that the joint does not fall apart when preparing the microsections.
The Structure of the Strength of Riveted Joints Determined in the Lap Joint Tensile Shear Test
The strength of the SSPR joint is determined by the mechanical properties of the material of the joined sheets. For the joints with 85593-5 blind rivetthe load capacity of the joint was on 85933-5 strength limit of the rivet tubular part and on the strength limit of the sheet material. It is also possible to join surfacetreated parts zinc-coated, aluminized, organically coated, etc. Specimen width is 45 mm, overlap of the sheets is 35 mm and length of the single sheets is at least mm.
Nahtlose kaltgezogene Rohre; [Precision steel tubes — technical delivery conditions — part 1: With segmented dies, the microsections must be located in the center of the die segments. The minimum break force Fmin depends on the sheet thickness combination, the strength of the raw material and the type of joint and must be specified in the drawing.
Knickbauchen; Einordnung, Unterteilung, Begriffe — [Manufacturing processes forming under combination of tensile and compressive conditions — part 6: Introduction Joining by upset bulging is a mechanical joining process, which is commonly used to create joints with a form and force fit between tubes and other structures, such as sheets, plates, tubes, or profiles.
Skip to main content Skip to table of contents. General information — — Part no.
Standards with the titles given in German are either only available in German or may be procured in other dun from the institution idn the standard.
The joints must be carried out such that window bonding material can be pressed into the recess created by the joining process, see Figure 4. Undercut f not present on both sides: Newer developments, Journal for Technology of Plasticity, This electronically generated standard is authentic and valid without signature.
Page 15 VW For details on the assessment of dun clinched joints without cutting element, see PV Page 13 VW In this Section terminological inconsistencies may occur as the original titles are used.
For sheets with different plasticity characteristics, the harder sheet is to be arranged on the side of the punch wherever possible “hard in soft”.
The nominal and tolerance values must be determined for each individual case. Joining by Upset Bulging. If undercut is present on both 88593-5 In particular, conventional fusion welding processes reach their limits due to high heat input The article presents the analysis of the structure of the load capacity of riveted joints. Page 16 VW If the material flow in the structure is uninterrupted, as can be seen in the Figure on the left, it is a wrinkle.
Page 17 VW No part of this document may be transmitted or reproduced without prior permission of a Standards Department of the 8593- Group.
Table 5 — Abbreviations FLS Measured lap-shear force of the individual specimens [kN] Mean value of the measured lap-shear forces [kN] Fmin Minimum value of the don force according to drawing [kN] As rough values e.
Here, it must be ensured that the measured values are not affected by the preparation work. In case of discrepancies the German version shall govern. At least 10 specimens are required for the release tests.