2N2219 DATASHEET PDF

2N2219 DATASHEET PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Megul Zuluran
Country: Andorra
Language: English (Spanish)
Genre: Politics
Published (Last): 10 March 2008
Pages: 188
PDF File Size: 8.47 Mb
ePub File Size: 17.8 Mb
ISBN: 784-7-60818-792-1
Downloads: 47663
Price: Free* [*Free Regsitration Required]
Uploader: Mazukazahn

2N Transistor Pinout, Specs, Equivalent & Datasheet

To make this current flow through the transistor ddatasheet value of base current I B can be calculated using the below formula:. TL — Programmable Reference Voltage. So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula: This resistor is connected to the base pin of the transistor dayasheet limit the current flowing through the base. This stage is called Saturation Region.

But it comes in a metal can package and can operate on voltages datassheet higher than what a 2N can datasgeet. So the value if R B will be. Amplifier modules like Audio amplifiers, signal Amplifier etc. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. The 2N is a NPN transistor and is normally used as a switch in many circuits.

  CSI 24C128 PDF

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. Where h FE, is the current gain of the transistor which in our case is The value of this current can be calculated by the required amount of current that will be consumed by the load. But this calculation will lead to the closest value to start with.

However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor. So to calculate the dataaheet value of the base we can use the formulae.

Complete Technical Details can be found at the datasheet given at the end of this page. As we know the transistor is a current controlled device meaning, we have pass some 2n221 I B thorough the base of the transistor to turn it on.

Current flows in through collector, normally connected to load.

2N2219 Datasheet, Equivalent, Cross Reference Search

Here lets us assume the load here consumes around mA maximum so our collector current I C mA. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Another important thing to keep in mind, while using a transistor as switch is the base resistor. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

  CONSTRUCTION PLANNING EQUIPMENT AND METHODS BY R.L.PEURIFOY PDF

Submitted by admin on 21 June Current Drains out through emitter, normally connected to ground.

Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. In our case for a collector current of mA we have to pass a base current of 16mA. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.